Description

The IFT3000-TQFP-TR is an electronic component model that falls under the category of IC Chips. It is part of the QUALCOMM IFR3000™ and IFT3000™ series of Rx and Tx IF/Baseband processors. These processors provide a significant reduction in cost, size, and pin count compared to previous generation products. They integrate the functionality of three Application Specific Integrated Circuits (ASICs) into two ASICs, offering IF-to-Baseband and Baseband-to-IF processing power, as well as Rx and Tx Automatic Gain Control (AGC) circuitry. The IFT3000-TQFP-TR is designed for use in dual-mode CDMA and FM portable cellular telephones, acting as an interface between the RF section and the digital processing circuitry of the telephone.

Specifications and features

IFR3000 Device Features:

• Supports IS-98 (CDMA) and IS-19 (AMPS) standards for dual-mode operation
• 2.7 to 3.15 V supply voltage
• Low current: 26 / 21 mA in CDMA Rx / FM Rx Modes
• Rx power control through 90 dB dynamic range AGC amplifier
• IF mixer for downconverting IF to analog baseband
• Low-pass filtering for CDMA and FM I- and Q-component baseband signal demodulation
• 4-bit ADCs convert CDMA I and Q analog baseband components to digital baseband
• 8-bit ADCs convert FM I and Q analog baseband to digital baseband
• Clock generators for CDMA / AMPS operation
• VCO for generation of Rx LO mixing signal
• I- and Q-channel DC offset control inputs drive baseband DC voltage offset to zero in CDMA and FM signal paths
• Operational Mode compatibility with the MSM2300™, MSM3000®, and MSM3100™ devices
• Enhanced features with MSM3000 device through three-line serial bus interface (SBI):
• Slotted FM Mode
• Selective power-down
• Mode selection
• 48-lead LQFP and 48-pin BCC packaging options for dense circuit assemblies

IFT3000 Device Features:

• Supports IS-98 (CDMA) and IS-19 (AMPS) standards for dual-mode operation
• Operates on 2.7 to 3.15 V supply voltage
• 8-bit DACs convert digital baseband signals to analog baseband
• CDMA and FM signal paths include lowpass filters for I and Q output waveform smoothing
• IF mixer upconverts analog baseband to IF
• Tx power control through 85 dB dynamic range AGC amplifier
• Programmable Tx PLL for generating Tx IF frequency
• VCO for generation of Tx LO mixing signal
• 8-bit general-purpose ADC with 3-input analog multiplexer and selectable input ranges
• Operational Mode compatibility with the MSM2300 and MSM3000 devices
• Enhanced features with MSM3000 device through three-line serial bus interface (SBI):
• Tx PLL phase-detector polarity
• Tx PLL programmability
• Punctured CDMA transmission
• Selective power-down
• Mode selection
• 48-lead LQFP and 48-pin BCC packaging options for dense circuit assemblies

Application Scenarios

The IFT3000-TQFP-TR is specifically designed for use in dual-mode CDMA and FM portable cellular telephones. It acts as an interface between the RF section and the digital processing circuitry of the telephone. Its compact size, reduced cost, and integration of multiple functionalities make it suitable for these application scenarios.

Comparison

• Significant reduction in cost, size, and pin count compared to previous generation products
• Integration of three ASICs into two ASICs
• IF-to-Baseband and Baseband-to-IF processing power
• Rx and Tx Automatic Gain Control (AGC) circuitry
• Operational Mode compatibility with other devices in the QUALCOMM IFR3000™ and IFT3000™ series

No specific disadvantages were mentioned in the provided information.